LOT-QuantumDesign
Our partner Macken Instruments

Thermal image plates

From Macken

Macken Instruments’ thermal image plates allow to see real time IR laser beams with high resolution. The characteristics of this instrument enable it to solve a wide range of problems.

We provide uncooled (models 22-A and 22-B) and water cooled versions (models 20-C and 20-D).

Further information

Theory of operation

The thermal image plate displays IR laser beam through the use of thermal-sensitive phosphors. When illuminated these phosphors fluoresce by a long wavelength ultraviolet light (3600 A). The intensity of the fluorescence decreases with increasing temperature.

When an IR laser beam strikes the thermal-sensitive surface, the absorbed energy raises the surface temperature and produces a corresponding thermal image. The produced pattern appears as a dark image on a bright fluorescent background when the surface is illuminated by an ultraviolet light. Different sensitivity ranges are obtained by using different phosphors and by varying the amount of thermal insulation between the phosphors and the anodized aluminum heat sink.

Any long wavelength, ultraviolet light can be used to illuminate the surface, but Macken Instruments’ lamp model 22-UV is the most satisfactory. Its small size and high-illumination level permit it to be conveniently positioned out of the working area.

The power density of CO2 laser beams ranges from those which can rapidly burn holes in firebrick to those that can’t be felt on the back of the hand. Eight different surfaces with overlapping sensitivities are used to smoothly span the power density range from 200 Watts/cm2 to 0.01 Watts/cm2. (The minimum detectable power for a focused beam is less than 0.001 Watts.)

Thermal image plate 22-A contains four surfaces which cover the power densities commonly obtained from CO2 laser beams as they emerge from the laser. The lower power densities usually found in optical systems and divergent beams are covered by thermal plate 22-B.

The physical dimensions of each thermal plate (22-A and 22-B) are 15.24 cm x 7,62 cm x 2.54 cm. Each side of these plates contains two sensitive surfaces which are 7.62 cm x 7.62 cm. The ultraviolet lamp (22-UV) measures 15.24 cm x 5,08 cm x 5.08 cm.

Power dissipation

A Thermal Image Plate device is capable of displaying beams up to 200 Watts. However, it must be removed from the beam and allowed to cool when there is a marked decrease in overall fluorescence. This occurs when the plate has absorbed 15,000 Watt seconds of power. Powers less than 30 Watts can be dissipated indefinitely.

Safety

Precautions have been taken to eliminate specular reflections from the Thermal Image Plate. Both the thermal-sensitive surfaces and the anodized aluminum have matte finishes and show little surface reflection at 10.6 microns. However, standard safety precautions such as wearing protective glasses should always be observed when working with IR lasers.

Thermal Image Kit

The thermal image plates 22-A and 22-B as well as the ultraviolet lamp 22-UV can be purchased separately or together in the form of a thermal image kit. When the kit is purchased, a hard plastic case is also included. Considering the wide range of power densities which can be obtained from non-uniform beams, we recommend an initial purchase of the thermal image kit.

Specifications

The following table gives the specifications of the eight surfaces measured at 8 to 12 microns. For use at 4 to 8 microns, multiply columns a, b and c by 2. For use at 2 to 4 microns, multiply columns a, b and c by 2.5.

Model number Surface number Normal sensitivity range (a) [W/cm2] Minimum power density (b) [W/cm2] Damage threshold (c) [W/cm2] Response time (d) [s] Resolution (e) [lines/inch]
22-A 1 60 - 200 16 800 <0.03 >300
2 30 - 100 8 600 <0.03 >300
3 15 - 50 4 350 0.03 300
4 7.5 - 25 2 200 0.03 200
22-B 5 3.3 - 11 0.9 100 0.06 100
6 1.5 - 5 0.4 44 0.15 50
7 0.4 - 2.4 0.06 24 0.2 100
8 0.06 - 0.4 0.01 4 1.0 16
20-C 1 60 - 200 16 800 <0.03 >300
2 30 - 100 8 600 <0.03 >300
20-D 3 15 - 50 4 350 0.03 300
3 7.5 - 25 4 200 0.03 200

a) The normal sensitivity range is the spread of power densities which can be easily viewed with no reduction in background illumination. The upper power density occurs when the surface becomes saturated, turning the area completely black and making it incapable of displaying any further detail within the beam.
b) The minimum-detectable power densities are the lowest power densities observable under the most favorable illumination levels. For this sensitivity the room lights must be dimmed and the level of ultraviolet illumination decreated to produce a dim fluorescence.
c) Damage threshold is the power density which produces a permanent change in the thermal- sensitive surface. This occurs at power factors at least four times greater than saturation. Therefore, when saturation occurs, a lower sensitivity surface should be used to display the beam.
d) The response time is the length of time it takes a change in the beam to be displayed as a change in the thermal image.
e) The resolution of a surface is the maximum number of dark and light line pairs which can be displayed with good contrast. For comparison, the resolution of a newspaper photograph is approximately 70 lines/inch. Two CO2 laser beams intersecting at an angle of two degrees produce an 80 line/inch interference pattern.

Ordering Information
51362 Thermal image plate, model 22-A, uncooled
51361 Thermal image plate, model 22-B, uncooled
51366 Thermal image plate, model 20-C, water cooled
51367 Thermal image plate, model 20-D, water cooled
51349-01 Ultraviolet lamp, model 22-UV with CE
51360 Thermal image kit, model 22-K (includes model 22-A, 22-B, 22-UV and fabric case)
Prices on custom thermal image surfaces are available upon request. These include larger sizes, models or coatings applied  to supplied parts.

Downloads

Thermal image plates
Water cooled thermal image plates

Contact

Stéphane Marin
Stéphane Marin

Contact

Quantum Design S.A.R.L.

Avenue de l’Atlantique
Bâtiment Fuji Yama
91940 Les Ulis
France

Phone:+33 1 69 19 49 49
E-mail:franceqd-europe.com
Stéphane MarinProduct Manager & Service Engineer
01 69 19 49 49
Write e-mail