Misuratori analogici di potenza laser
da MackenI Power Probes analogici indicano la potenza laser misura su una scala di lettura calibrata. Il Power Probe Macken è uno strumento di misura completo costituito da un assorbitore, da un meccanismo di misura della temperatura e da un quadrante di lettura con una manopola di azzeramento integrata. Prima della misura lo strumento viene azzerato e poi l’assorbitore, posto all’estremità opposta dello strumento rispetto al quadrante di lettura, viene esposto alla radiazione laser per uno specifico intervallo di tempo. Una volta che il Power Probe è stato rimosso dall’esposizione al fascio laser, è possibile leggere il valore di potenza media misurata indicato sul quadrante di lettura.
La misurazione ha una durata complessiva di circa 1 minuto. Inoltre, in caso sia necessario eseguire un certo numero di misure in rapida sequenza, è possibile raffreddare velocemente l’assorbitore immergendolo in acqua tra una misura e la successiva.
Caratteristiche
- Lassorbitore sufficientemente compatto ne permette linserimento tra i componenti ottici per la misura di potenza laser senza alterazione del set-up
- Tempo necessario per la misura di potenza di circa 1 minuto
- Coating dellassorbitore resistente alle abrasioni meccaniche e allimmersione in acqua
- Semplice meccanismo di regolazione dello zero
- Il telaio realizzato interamente in metallo garantisce lunga durata al Power Probe
Specifiche
Accuracy [%] for all ±5
Repeatability [%] for ±1.5
Explanation of Damage Threshold
High power lasers that can cut metal can also damage the absorbing head of a power probe if the beam is too concentrated. It has been found that it is not possible to quote a single number for the power density that will damage a power probe. The damage threshold is also a function of the total power in the beam and whether the absorbing head is moved during the exposure.
For a CO2 laser, there is no loss in absorbtivity (no damage) when the coating is heated to the point where it exhibits a visible bleached spot but no other change. There is damage when metallic areas can be seen on the surface. In operation, power densities should be kept substantially below the indicated damage threshold.
Model | Power Range [W] | Demage Thershold [W/cm2] | Exposure Time [s] | Division [W] | Absorbing Head [cm] | Length [cm] | Weight [g] | ||
---|---|---|---|---|---|---|---|---|---|
P20Y | 0-20 | 3000 | 30 | 0.2 | 4.58 x 2.54 | 22 | 89 | ||
P50Y | 0-50 | 3000 | 20 | 0.5 | 4.58 x 2.54 | 22 | 98 | ||
P100Y/ | 0-100 | 3000 | 20 | 1 | 5.08 x 3.18 | 22 | 120 | ||
P100C | 0-100 | 10000 | 20 | 1 | 5.08 x 3.18 | 22 | 120 | ||
P200Y | 0-200 | 2500 | 20 | 2 | 5.08 Ø | 22 | 157 | ||
P200C | 0-200 | 7000 | 20 | 2 | 5.08 Ø | 22 | 157 | ||
P500Y | 0-500 | 2000 | 20 | 5 | 5.08 Ø | 22 | 183 | ||
P500C | 0-500 | 4000 | 20 | 5 | 5.08 Ø | 22 | 183 | ||
P1000Y | 0-1000 | 1750 | 20 | 10 | 6.35 Ø | 22 | 287 | ||
P1000C | 0-1000 | 2500 | 20 | 10 | 6.35 Ø | 22 | 287 | ||
P2000Y | 0-2000 | 1200 | 20 | 20 | 7.62 Ø | 22 | 522 | ||
P2000C | 0-2000 | 1500 | 20 | 20 | 7.62 Ø | 22 | 522 | ||
P4000Y | 0-4000 | 900 | 20 | 25 | 8.89 Ø | 28 | 753 | ||
P4000C | 0-4000 | 1100 | 20 | 25 | 8.89 Ø | 28 | 753 | ||
P10KY | 0-5000 0-10000 | 750 | 20 10 | 50 100 | 8.89 Ø | 28 | 1144 | ||
P10KC | 0-5000 0-10000 | 900 | 20 10 | 50 100 | 8.89 Ø | 28 | 1144 | ||
Wavelength for Y-Models: 900 - 1250 nm, Wavelength for C-Models 8 - 11 µm |
Conical Laser Power Probes for high power density
Conical Head Power Probes are used to measure high power density CO2 laser beams which may damage the standard flat surfaced Power Probes. The conical absorbing cavity exhibits a high heat dissipation. There are two models of Conical Power Probes: C2K, C4K and C10K. Table 1 below gives specifications for these models. Table 2 gives approximate damage threshold for both the flat surface and conical power probes.Conical Power Probe Specifications | |||
---|---|---|---|
Model | C2K | C4K | C10K |
Primary Power Range [W] | 0 - 2000 (20 sec) | 0 - 4000 (20 sec) | 0 - 10000 (10 sec) |
Alternative Power Range [W] | - | - | 0 - 5000 (20 sec) |
Absorbing Head, Ø [cm] | 6,2 | 7,0 | 7,6 |
Conus, Ø [cm] | 5,08 | 5,7 | 6,35 |
Weight [g] | 535 | 1000 | 1160 |
Accuracy [%] | ±5% | ±5% | ±5% |
Repeatability [%] | ±1.5% | ±1.5% | ±1.5% |
Approximate Damage Threshold | |||
---|---|---|---|
Power in a CO2 laser beam [W] | Exposure Time [s] | Flat Probes1 [W/cm2] | Conical Probes2 [W/cm2] |
100 | 20 | 10000 | 15000 |
200 | 20 | 7000 | 11000 |
500 | 20 | 4000 | 8000 |
1000 | 20 | 2500 | 5000 |
2000 | 20 | 1500 | 3000 |
5000 | 20 | 1100 | 2200 |
10000 | 10 | 900 | 1800 |
1 Model P500C, P1000C, P2000C, P10KC, H3C and H4C 2 Model C2K, C4K and C10K |
Downloads
Contatti

Ing.
Alessandro
Baratti
Navigazione
Categorie
Contatti
Quantum Design s.r.l.
Via Francesco Sapori, 27
00143 Roma
Italy
Telefono: | +39 06 5004204 |
Fax: | +39 06 5010389 |
E-mail: | italyqd-europe.com |