High-speed streaming cameras

PROMON U1000 runs a modern 2.3 MegaPixel detector with 1900 x 1200 active pixels at a full frame rate up to 150 frames/sec. When reducing the resolution frame rates up to 3145 fps stunning data rates are possible as well.

Promon U-Series cameras are cost effective, easy to use and easy to install cameras for industrial and scientific applications.

• 1900 x 1200 pixels resolution
• 150 fps
• USB3 based camera that takes images with 640x480 pixels @ 817 frames/sec
• Stunning data rate of 200+fps
• Available in color / monochrome
• Installation of Imaging Studio Software on as many PC as required
• Records directly into PC RAM and HD

The Promon U800 uses a CMOS detector with 1280x1024 active pixels for high-speed recording. The miniature camera achieves a frame rate of 210 Hz in full frame. In the so-called windowing mode, fewer pixels are read out and higher frame rates of up to over 1680 frames per second are achieved. The smaller image windows can be flexibly selected and adapted to the application situation. Thanks to the high-intensity detector, there is little need to illuminate the scene to be captured. The Promon U800 comes with the powerful but easy-to-use control and readout software Imaging Studio V4. 
Using streaming, minute or hour-long sequence recordings are stored directly to a hard drive. The Promon U800 is housed in a small case, making it easy to attach to frames in process. The sensor is known for high image quality and sharpness.

• 1280 x 1024 pixels
• Trigger external or in the image
• > 3000 fps in ROI
• USB3 based miniature camera that takes images with 640x480 pixels @ 750 frames/sec
• Stunning data rate of 200+fps
• Available in color / monochrome
• Piloted by the AOS Imaging Studio V4 software
• Records directly into PC RAM and HD

Promon Scope G4 is a complete, simple, fully mobile high-speed camera system. Thanks to the new, powerful built-in battery, PromonScope can work for up to 3 ½ hours without mains power. A recording time of up to 30 minutes at a time on the built-in SSD is possible, even longer at reduced resolution. Operation takes place on the 13.3" touch screen. The high-speed camera system Promon Scope G4 sets new standards for portable high-speed recorders. PromonScope G4 is available with 1280x1024 pixel black/white or colour detector. The system is designed for mobile applications and is controlled with intuitive touch screen operation - thanks to its robust construction, even in demanding environmental conditions. Nevertheless, PromonScope G4 is not only intended for industrial use but also for fast, constantly changing applications in research. The high image resolution makes the smallest details of the process visible and enables a detailed analysis of the process. In addition, external analogue signal sources such as voltages, circuit states or PLC signals can be recorded image-synchronously and displayed in the video. If desired, other camera models of the Promon-U series can also be used in the PromonScope.

Promon Scope G4 Twin expands the standard system to a 2-camera system in which one camera functions as a master and one camera as a slave. The cameras can be synchronised or work independently, but can be operated and read out together by the PromonScope touchpad. This makes it possible to analyse an event simultaneously in 2 places. The two cameras do not have to be equipped with the same detector, so that a colour camera can be controlled simultaneously with a black and white camera, or two cameras with different pixel counts.

• 1280x1024 pixels or 1900*1200 pixels
•  Up to 3500 fps in ROI
•  Immediately ready for use without setup
•  Recording time up to 80 minutes
•  Light sensitive
•  Portable and robust
•  Camera head only 30 x 30 x 30 mm
•  Operating time over three hours (Li-battery)
•  13.3" touch screen
•  Twin camera solution available

Promon Scope GO 4 is a truly portable handheld high-speed imager for mobile use. It is ideal for temporary industrial troubleshooting, setup and fine-tuning applications. It is a complete set, consisting of controller, camera, lens, lights, mounting utilities.
 

Promon Scope GO 4 uses a 10.5“ Tablet controller with GO 4 software pre-installed, ready to go. The controller is mounted in hand held bracket for easy mobile use. The camera might be attached to the bracket with locks for USB3 cables. To ensure full mobility for various applications, the camera can be placed anywhere using a 3 m USB 3 cable

You can easily carry the device from place to place without having to set up a complete system every time. A bright, rechargeable LED headlamp complements the mobility and ensures easy handling.

Thanks to the powerful battery, the Promon Scope GO 4 can stay in recording mode for up to three and a half hours without recharging. Minutes of high-speed recordings can be stored on the internal SSD drive. The system allows various triggering options.

Promon Scope GO 4 is delivered with our well reputated software Imaging Studio V4 TOUCH. Imaging Studio V4 TOUCH allows camera setting, sequence acquisitions, triggering, display even of multiple sequences side by side and data export in a comfortable, comprehensive, but easy to use software. Imaging Studio V4 TOUCH can be used in different language settings to increase the comfort of handling.

Promon Scope GO 4 is delivered with a flexible zoom-lens for close and medium distant objects. Thanks to its C-mount, different objectives can be easily mounted for almost all applications.

• 1280x1024 pixel
• Color or monochrome
• 203 fps full frame, up to 3500 fps in ROI
• Ready to use without setup
• All components portable ready to use
• Camera head can be used mobile or remote
• Operating time over three hours (Li-battery)
• 10.5" touch screen