Notre partenaire

Contrôleurs de température cryogénique

Lake Shore Cryotronics

Les contrôleurs de température pour les applications cryogéniques sont basés sur une régulation PID en boucle fermée, également appelée régulation à rétroaction. Grâce à cette caractéristique, ils couvrent une gamme de températures de 100mK à 1 500K. Les boucles de régulation ont une puissance de chauffe allant jusqu'à 100W. Lors de la régulation PID, le contrôleur tente de maintenir la charge à la valeur exacte de consigne entrée par l'utilisateur. Elle peut être saisie en unités de capteur ou en température.

Easy product selection for quick inquiries

Go to inquiry system

Caractéristiques

Plage de température de 100mK à 1.500bK
Jusqu'à 4 sorties contrôlées par PID avec une puissance maximale de 100W
Large gamme de capteurs de température pris en charge
Interfaces Ethernet, USB et IEEE-488

Plus d'informations

More Information about each model:

Model 325 Temporairement indisponible

Closed loop PID control
The PID control equation has three variable terms: proportional (P), integral (I), and derivative (D). The PID equation is:

where the error (e) is defined as: e = Setpoint – Feedback Reading.

The proportional term, also called gain, must have a value greater than zero for the control loop to operate. The value of the proportional term is multiplied by the error (e) to generate the proportional contribution to the output: Output (P) = Pe. If proportional is acting alone, with no integral, there must always be an error, or the output will go to zero. A great deal must be known about the load, sensor, and controller to compute a proportional setting (P). Most often, the proportional setting is determined by trial and error. The proportional setting is part of the overall control loop gain, as well as the heater range and cooling power. The proportional setting will also need to change if either of these changes.
In the control loop, the integral term, also called reset, looks at error over time to build the integral contribution to the output:

By adding integral to the proportional contribution, the error that is necessary in a proportional-only system can be eliminated. When the error is at zero, controlling at the setpoint, the output is held constant by the integral contribution. The integral setting (I) is more predictable than the proportional setting. It is related to the dominant time constant of the load. Measuring this time constant allows a reasonable calculation of the integral setting.
The derivative term, also called rate, acts on the change in error with time to make its contribution to the output:

By reacting to a fast-changing error signal, the derivative can work to boost the output when the setpoint changes quickly, reducing the time it takes for temperature to reach the setpoint. It can also see the error decreasing rapidly when the temperature nears the setpoint and reduce the output for less overshoot. The derivative term can be useful in fast changing systems, but it is often turned off during steady state control because it reacts too strongly to small disturbances or noise. The derivative setting (D) is related to the dominant time constant of the load.

Manual output
Manual output can be used for open loop control, meaning feedback is ignored and the heater output stays at the user’s manual setting. This is a good way to put constant heating power into a load when needed. The manual output term can also be added to the PID output. It is possible to set an output value close the one needed and let the controller do the fine tuning to reach the set point.

NOTE: Manual output should be set to 0 when not in use.

Caractéristiques techniques

Model 372 AC Resistance Bridge

Temperature measurement and control capabilities for dilution refrigerators (DRs)
Temperature control below 100mK
Patented noise rejection technology*
AC measurement signals
Low noise signal recovery

*U.S. Patent #6, 501, 255, Dec., 2002, "Differential current source with active common mode reduction," Lake Shore Cryotronics, Inc.
Model 350 Cryogenic Temperature Controller

Ideal for use with He-3 systems and other ultra-low temperature refrigeration platforms
Down to 100 mK
Optimized performance with Cernox® RTDs
Minimal self-heating
High resolution measurement
4 independent control loops and a broad range of I/O configurations
4 PID-controlled outputs: 75 W warm-up heater, 1 W sample heater, and 2 auxiliary 1 W ±10 V outputs

Model 336 Cryogenic Temperature Controller

Operates down to 300 mK
Two PID control loops: 100 W and 50 W into a 50 or 25 Ω load
Autotuning automatically collects PID parameters
Ethernet, USB and IEEE-488 interfaces
Supports diode, RTD, and thermocouple temperature sensors
Sensor excitation current reversal eliminates thermal EMF errors for resistance sensors

Model 335 Cryogenic Temperature Controller

Operates down to 300 mK
Two configurable PID control loops providing 50 W and 25 W or 75 W and 1 W
Autotuning automatically collects PID parameters
USB and IEEE-488 interfaces
Supports diode, RTD, and thermocouple temperature sensors
Sensor excitation current reversal eliminates thermal EMF errors for resistance sensors

Model 325 Cryogenic Temperature Controller

Operates down to 1.2 K
Two sensor inputs
Supports diode, RTD, and thermocouple sensors
Sensor excitation current reversal eliminates thermal EMF errors for resistance sensors
Two autotuning control loops: 25 W and 2 W maximum
Control loop 2: variable DC voltage source from 0 to 10 V maximum
IEEE-488 and RS-232C interfaces